Z1 Pro (original) stock Android 7.0

bencebacsi

skycrow67 replied at 2018-3-29 14:39
Edited by skycrow67 at 2018-3-29 15:08 \n\n Edited by skycrow67 at 2018-3-29 14:45 \n\n
Do i need m ...

Maybe you have a hardware issue. Even the first batch of UMIDIGI Z1 Pro (shipped with stock Android) can work properly with the UMI OS system.
However, that is officially not supported to flash UMI OS on Z1 Pro devices shipped with stock Android. Since you completely erased the flash chip of your phone, anything unexpected could happen.

OnlyForYou

Hello, yesterday I updated my Z1 Pro to the latest version via FOTA,
After the update, the cell phone starts normally, but after a few seconds of powering up, it stays on the blue screen, after being able to continue to control the cell phone, (move to the screen level, perform sounds, receive alerts from the applications) normal, it just looks all blue!

If it restarts, switch on again normally, but after a few seconds everything turns blue again.
Inferring use ...

What do you recommend me to do?

bencebacsi

OnlyForYou replied at 2018-4-2 18:22
Hello, yesterday I updated my Z1 Pro to the latest version via FOTA,
After the update, the cell phon ...

Hi,
Flash the same version with SP Flash Tool in firmware upgrade mode.

batcha76

Can some one help me that when i want to disconnect a  call, the screen does not wakeup to disconnect the call. I have to either press the power button or the home button to wakeup the screen. The proximity sensor does not realise that the phone has been removed from my ear.

is there any one having the same issue or any update is required from UMI support to overcome this issue.

ToughCookie

Hello, maybe someone could help me with this? My Z1 Pro died after 2 months. The battery was around 10% when it happened; I charged it many times, for long periods of time and nothing. The red led turns on when I plug it and it blinks if I press Power + Volume Up, but apart from that it is dead.

I tried flashing it but it is not recognized by the computer at all (no usb sound when I connect it). I tried installing every driver I found online but I can't make it work. Is this a hardware problem? Should I give up? Thanks so much, this is driving me insane.

bencebacsi

ToughCookie replied at 2018-4-14 10:03
Hello, maybe someone could help me with this? My Z1 Pro died after 2 months. The battery was around  ...

Hi,
Your battery is probably over discharged but your USB cable can be damaged as well, or your computer could see your phone. First try to use another USB cable and charger. Even with intact accessories, now it might need a longer time to start the charging process, up to 12 hours.

ToughCookie

bencebacsi replied at 2018-4-16 07:05
Hi,
Your battery is probably over discharged but your USB cable can be damaged as well, or your com ...

Thanks so much for your reply; unfortunately the usb cable works fine, I use it for everything else with no problems. I left the phone charging for 12 hours and more with no results at all.

bencebacsi

ToughCookie replied at 2018-4-17 21:11
Thanks so much for your reply; unfortunately the usb cable works fine, I use it for everything else ...

Then there's no other solution but the battery should be removed and charged using an external power source. You need to take your phone to a repair shop.

Funkfreaker

batcha76 replied at 2018-4-12 19:20
Can some one help me that when i want to disconnect a  call, the screen does not wakeup to disconnec ...

Same problem here, even after a sp flash tool reset

Funkfreaker

Still one very big question, will there be an update for the Z1 Pro, because it is not that long ago that the phone is been releases. I would be very sad if this phone will be forgotten.
Do you have any news bencebacsi?