UMi Iron Pro V3.02 (0107) Discussion

kaju666 · Post time 2016-1-11 22:19:02

capitanbelico replied at 2016-1-11 21:14
i updated using Rootjoy it was very easy and clean.
i backed up apps and contact and restore after u ...

the same in my afte rupdate, sometimes problem with fingerprint unlock.

i wondering if anyone from umi team read those comments.

Green_and_Fat · Post time 2016-1-13 16:51:56

Updated yesterday, rootjoy can't find firmware automaticaly, use ROM from romjd, but all is ok.
I need the hardware button can be swapped too, hope you add this feature in future versions, thanks for this phone.

P.S. Sorry my google translate

Armada17 · Post time 2016-1-15 18:41:08

When fxed clicks in the headphones? I can not normally listen to music, annoying

capitanbelico · Post time 2016-1-15 23:15:15

capitanbelico replied at 2016-1-9 22:23
can i upgrade via update in phone?
have dis upgrade fix some camera issues and warming's phone?

sorry, i mean issue like phone´s heating and bad performance of the camera, the camera sensor is good and can do more than do now.

Green_and_Fat · Post time 2016-1-19 15:12:45

При отправке/получении текстового сообщения, вместо времени отправки/получения появляется надпись "имя неизвестного исполнителя". Эта надпись находиться в файле resources.arsc из Mms.apk Можете ее совсем удалить, или исправить на "только что"?

Russian language, when sending / receiving text messages, instead of the time of sending / receiving appears "имя неизвестного исполнителя".
Can completely remove it or change, for example, on "Последнее" or "Недавнее"?

kayslay86 · Post time 2016-1-19 15:39:40

Edited by kayslay86 at 2016-1-19 18:20 \n\n Edited by kayslay86 at 2016-1-19 17:52 \n\n Edited by kayslay86 at 2016-1-19 17:50 \n\n Edited by kayslay86 at 2016-1-19 16:22

Hi Team UMI,

you did some changes concerning Bluetooth Connectivitiy ? I`ve got a SONY BM10 BT Dongle connected with my DENON X1000 (reseted them all) but my UMI Iron Pro isn`t able to connect

first I had problems to find my BM-10 with the phone - after I was able to see and try to connect a window oppened which asked me if this BT device is a trusty one so I accepted but an error occured with told me "wasn`t able to connect please try again <- smth like that, it was a longer sentence but no specifiv error-code"

add. I`ve tried to connect via BT with my WindowsMobile 8.1 Phone (Samsung Ativ S) but the same error occured.

still 3.01 and I want to flash to 3.02 but I would like to know if there were some change before I do it

#### update ####

connected with a Sony Z2 - Pairing Code was shown and I was able to send a picture but both devices mustn`t accectp the "thrusty device SMART LOCK screen" - after Ì`ve send my pic both devices accepted "this is a thrusty device SMART LOCK" but the same Error occured (Z2 told us to resett the UMI IronPro and my UMI Iron Pro told to reset the Sony Z2 )

#### compare ####

Bluetooth Options

http://www.devicespecifications.com/en/model/b17837b4

BR

Angel_UMI · Post time 2016-1-20 07:04:50

Iron Pro has been tested connecting to different bluetooth devices (car bluetooth, speaker,another phone, laptop, and in all of these connection was successfully. Iron Pro which we made test has 3.02 installed

Angel_UMI · Post time 2016-1-20 07:11:09

capitanbelico replied at 2016-1-11 21:14
i updated using Rootjoy it was very easy and clean.
i backed up apps and contact and restore after u ...

After update to 3.02, front camera can be used normally without any problem. Did you arrived to try front camera before restore apps after update?

Fingerprint is working good too. Tests were made configuring one finger of right hand, and another finger of the left hand.
After configuring, both fingers are working perfectly without failures.

You should try to flash again and before restore any app try to use front camera. If is working fine, any of apps restored could be the problem.

kayslay86 · Post time 2016-1-20 15:55:50

Angel_UMI replied at 2016-1-20 07:04
Iron Pro has been tested connecting to different bluetooth devices (car bluetooth, speaker,another p ...

Hi Angel,

I updated successfully to 3.02. (wow this Backup / Flash Software is awesome and it was so easy - keep going : ) )

and tried to connect again to my SONY BM-10 (resetted BM-10 and cleared Cache/Data Bluetooth processalso) but he doesn`t want to connect : /

additional I`ve still problems with the Audio Output / Viper Equalizer - still the same "plop" when changing tracks, and a disturbance which I haven`t read here before
(tested with JBL Tempo on-ear , Fischer On-ears, Samsung In-Ears - tried add. via MusicPort Aux-In to my Panasonic HiFi System and there wasn`t a disturbance but I think this System filter these disturbance very good but my Headphones aren`t able to do that. <-- SOMEBODY ELSE GOT THIS PROBLEM?

I tried to deactivate Viper and/or installed it again with the different profiles only to check how to get the rid of these freaky grainy noises (UMI Equalizer was deactivated, no Enhance, no AudioBooster was set on)

is there something what I can do ?

Thanks for your help
BR from Germany

capitanbelico · Post time 2016-1-21 21:22:39

Angel_UMI replied at 2016-1-20 07:11
After update to 3.02, front camera can be used normally without any problem. Did you arrived to tr ...

ok, angel.
i installed flyme 4.5.3L that appear on rootjoy and was good, but fingerprint not working and camera sucks.
after that i flasshback to v3.02 and restore apps and everthing, just after that i could see your request, so, I will resflash as you said and i ll let you know how it works for me.