UMIDIGI Z Pro V7.01_20170605 Android 7.1.1 ROM - SPFT + OTA release

pucap

vinchenzogt replied at 2017-7-5 12:46
Edited by vinchenzogt at 2017-7-5 12:54 \n\n

Do i have to push the power button when firmware upgr ...

No, you don't.
Switch off the phone and keep it disconnected from the PC. Then follow the instructions in the post; once you have loaded the scatter file and selected Firmware Upgrade option in SP Flash Tool, press the Download button and then connect the device to the PC with the USB cable (keep it off!). The process will start; if it doesn't work, try again from the beggining. If still doesn't work, try again but select Download only instead of Firmware Upgrade.

pucap

vinchenzogt replied at 2017-7-5 12:46
Edited by vinchenzogt at 2017-7-5 12:54 \n\n

Do i have to push the power button when firmware upgr ...

... and keep it with 6.0, because it's clear than UMIDIGI has forgotten its Z Pro users and is only working on its new models.

vinchenzogt

\n\nERROR: STATUS_ERR (0xC0010001) Firmware android 6.0 not supported

scroful

chooks06 replied at 2017-7-3 21:28
Friends, I'm not a geek nor a noob.. If you're brave enough to do SPFT flash, you would be surprised ...

i think you too money ! i bought umidigi z pro because i saw the spec. Good camera etc...at home, poor camera, my old samsung s3 made better, lots of bugg etc. For me 229 euros its a big money, and i want to have a phone who have ggod functionnaly. In fact the solution was to install another rom of umidigi clone, Noa H10 to have a phone who is not perfect but better. Where is the fast charge ? Perhaps at laboratory of umidigi, but not on my z pro in france. If i could i asked umidigi to refund my phone and buy a xiaomi ou samsung. Shame umidigi, like Verne with apolo lite the other phone i bought in china.

radoo

Just to clarify: installed Android 7 with Flash tool, did setup as new phone, no reinstallation, even with nothing extra installed on the phone, and the phone reboots. It was working okay for almost 12 hours, then plenty of reboots, even multiple times in a row.

Went back to Android 6, i have no issues with reboots, but there's a lot of other smaller issues on Android 6 that make it a bad experience.

I've temporarily switched to a Moto Z, but I still hope there's an Android 7 in the works that can make the UMI Digi Pro useful again.

pucap

radoo replied at 2017-7-6 01:03
Just to clarify: installed Android 7 with Flash tool, did setup as new phone, no reinstallation, eve ...

Just to clarify: you don't need to clarify how bad this ROM is, it's totally clear.
A month since it was released and all we've got is ... nothing! Well, yes, a completely unacceptable treatment from the company and from bencebacsi, its representative in this forum.

Ricey155

New update promised for 2moro? Phones fine other than reboots

Battery is good and honestly I'm happy with it over Verne's effort, judgement is open till update

AlexandreM.

Ricey155 replied at 2017-7-6 17:53
New update promised for 2moro? Phones fine other than reboots

Battery is good and honestly I'm hap ...

i wait too

Gig4byte

Well, technically it's already tomorrow in Shenzhen...

pucap

A great mobile is little useful without a good software. It's enough for me, I'm triying to sell both my Z and Z Pro and buy another mobile, perhaps a Xiaomi, who is more concerned with maintaining good software.
Bye UMIDIGI.