UMIDIGI Z2 Pro V1.0_20180926 ROM - SPFT + OTA release

andreibu

ricalv replied at 2018-10-25 21:24
Edited by ricalv at 2018-10-25 21:26 \n\nAfter much more tampering, managed to get vowifi working a ...

Hello. Can you please tell us the procedure for activating VoWifi?
I was able to enable only VoLTE.
Thank you

Luigirox

Bugs to be fix.

1-) absence of notifications in the status bar
2-) proximity sensor not work in calls
3-) in total darkness synchronize taking photo with the flash.
4-) Camera app to remember your last settings

Karthikeyan

I got new FOTA update today ..
Version :: umidigi_z2pro_v1.0_20180823_20181024_1600...
What is this update fixes ??

ghost45

New Upgrade...good news!

dido

\n\nWith new update, the camera is still very bad... The doubled cameras is useless. No working bokeh effect , no 4k video...

Felix123

Saenz4931 replied at 2018-10-25 22:29
After many attends of installing the MTK and work arounds, that was the only way I was able to fla ...

So basically you where unsuccessful in installing the drivers and it worked without drivers via the mentioned method? Thx!

ricalv

\n\nHello everyone,A new update has come out, and it seems some of the problems have been addressed at last
After the update to UMIDIGI_Z2_PRO_V1.0_20180823_20181024-1600, this is what i have seen.
My proximity sensor is working again, at last.
The phone signal has increased, in places where in previous firmware I was getting about 3 bar I'm now getting almost full signal, great improvement.
All security access are still working.
VoLTE works fine, signal is par to other phones side by side to this one full LTE/4G signal and showing volte sign on screen.
Volte settings having to be inserted manually to get it working.
VoWifi works perfect, also settings inserted manually as it doesn't auto provission.
WiFi 5Ghz works but is still very unstable.
WiFi 2.4Ghz connects but is very unstable and loses connection very often.
I have found out that if you go to wifi settings, wifi preferences and disable network rating provider the wifi is a bit more stable, but still has to be fixed.
And now to the still most disappointing part of this phone the   quad lens camera , ha ha
The Camera works, that's about it, I don't think the camera software included with the phone can even handle the secondary camera as if you cover the lens there is no difference in the photos, the 8mp secondary camera does nothing or is not activated by the software.

motty93

Where is UMIDIGI_Z2_PRO_V1.0_20180823_20181024-1600??
I didn't find this in ROM FORUM.

Felix123

bencebacsi replied at 2018-10-24 00:06
Hi,
Of course I test and double check every OTA files before publishing. On the other hand, just a ...

So, managed to upgrade via SFTP, NO DRIVERS installed.
What I did, others might find helpful.
I was on the UMIDIGI Z2 Pro V1.0_20180914 ROM (local OTA installed)
Chose the UMIDIGI Z2 Pro V1.0_20180920 ROM for SFTP
Started SP Flash tool, in Firmware upgrade mode, did the necessary steps, clicked Download. THEN, whit the phone powered down, held the POWER BUTTON and VOLUME UP BUTTON till the SP Flash tool started transfering (in my case 1-2 seconds)

Once it was finished, booted up just fine, and voila, got notification about new OTA (vers 926), did the upgrade via OTA, rebooted, boom, got a new OTA update to 20180823_20181024_1600.

ricalv

andreibu replied at 2018-10-25 23:31
Hello. Can you please tell us the procedure for activating VoWifi?
I was able to enable only VoLTE ...

Hello,
I managed to get it done in the following manner,
First of all make notes of your providers information, if you already have a working internet connection keep a note of those parameters.
I've found that the best combination for the providers I use, Orange and Movistar in Spain is:
First the Internet APN
fill in with the parameters for your provider
APN Protocol = IPv4 & IPv6
APN Type = default,supl,agps
Bearer = unselect Unspecified and select all others
MVNO type = IMSI
MVNO value = the one for your provider, ie. Orange is 21403x you normally get this by joining together MCC & MNC codes

Second APN is the IMS (VoLTE), only fill in the following, everything else leave blank
Name: IMS
APN: ims
MCC: the one in your providers APN
MNC: the one in your providers APN
Bearer unspecified
MVNO type: IMSI
MVNO: your providers IMSI code
The third APN is your MMS APN, fill in with your providers parameters.


If you're using dual sim you duplicate these settings adjusting the MCC, MNC & MVNO values for each provider
I have tried with orange, movistar and Yoigo, and it only works with orange and movistar.