UMIDIGI A5 Pro V1.1_20190622 ROM - SPFT release

bencebacsi Post time 2020-2-12 15:41:06 | Show all posts [Copy link]
4 3733
View: 3733|Reply: 4

UMIDIGI A5 Pro V1.1_20190622 ROM - SPFT release

[Copy link]
Post time 2019-7-4 22:42:30 | Show all posts |Read mode
This is the SP Flash Tool of the
V1.1_20190622 system software
for UMIDIGI A5 Pro


Flash tool operation is recommended to experienced users only. If you are not yet an experienced flash tool user, please carefully read the flash tool tutorial before proceeding, and strictly follow each instruction.

Except if an authorized or responsible expert directly asked you to do that,
never format the flash chip of your device or you instantly lose your warranty!

UMIDIGI A5 Pro receives all updates automatically via FOTA method. You need this tool only in case of emergency (if you've bricked your phone), if you want to apply a clean install or if you want to clear all root access and custom recovery to make your phone able to receive FOTA updates again. Moreover, flashing with SPFT is the only option to repair (replace) damaged system software.




Changelog:
First release for manufacturing

FOTA version: UMIDIGI_A5_Pro_V1.1_20190622_20190622-1747


--------------------------------------------------------------------------------
SP Flash Tool
Resources:


Flashtool tutorial: http://bit.ly/SPFTguide

Extract the .rar file before use. The scatter file (MT6765_Android_scatter.txt) is inside the extracted folder, together with the other components


VCOM driver: Windows 10 already automatically can install it (if your computer is connected to the internet) or you can use this: MTK_Driver_Auto_Installer_SP_Drivers_20160804.exe


Here's an optional solution to start the flashing process on your UMIDIGI A5 Pro if the standard method doesn't work.
It's especially useful if your phone is bricked or is stuck in bootloop
1. Connect your UMIDIGI A5 Pro to USB.
2. Start the flashing process with the Download button in the flasher app.
3. Press and keep pressed the power button of your phone until the flashing process starts (red bar appears at the bottom of the app window), then release it. In this process you have to keep the power button pressed for about 10 seconds.
4. Wait until the flashing process finishes.



Kind request from users:
Please report any kind of new issues you experience after installing this update only if you've already flashed this ROM with SP Flash Tool in Firmware Upgrade mode. In rare cases a FOTA update can cause more or less serious malfunctions but that means only the update process went wrong, not a badly developed ROM. An updated stock ROM, especially related to the basic functions will not cause any new issues but will solve some of the existing ones.

0

threads

2

posts

8

credits

New Member

Rank: 1

credits
8
Post time 2019-8-1 17:11:28 | Show all posts
Edited by Saldana at 2019-8-2 17:32  

So I know there’s only so much that can be addressed online, but giving it a shot.

I have a Mitsubishi h2i inverter mini split with a branch box. 2 ceiling units, one floor unit. 1 ceiling is in 2nd floor bedroom (12,000 BTU), 1 wall is in kitchen (12,000 BTU) 1 ceiling is in 2nd floor garage apartment (18,000 BTU). Outdoor unit is 36,000 BTU.

System was installed in May 2017, just over 2 years in. Bedroom and kitchen units were used fairly often summer of 2017. Heat on all 3 worked fine winters of 18 and 19. A/C apparently worked all the summers, but this summer, I’ve discovered the garage apartment unit will start blowing warm air with all 3 units going. It’s sporadic, doesn’t always do it. But when it’s hot outside, it doesn’t stay blowing cold long. The outdoor unit barely revs up with all 3 going. I had my HVAC installer come out to check it. At the time it was blowing warmish air. They checked the pressure, appeared fine. No errors according to the beach box. Killed power on all 3, and apparently changed what the tech called “channels” on the branch. Fired all back on and they were apparently fine. (3 weeks later) Had all 3 going tonight, garage apartment unit blowing warm again. Turned it off and back on 60 seconds later. Then killed the kitchen unit. Went back to check and hour later, apartment was cool. I’m planning to call them again and have them back out here with what I’ve found.

Any insight about what is causing this? I’m questioning if outdoor unit was sized properly. Any input is appreciated!commercial kitchen equipment

0

threads

1

posts

8

credits

New Member

Rank: 1

credits
8
Post time 2019-7-15 13:25:32 | Show all posts
Edited by JainJude at 2019-7-16 06:20  

I brought the Umidigi one pro a few months ago. I have had zero problems with the phone, really happy with the phone over all.

But recently I was using the camera for work it was working fine, I came to use it again and it refused to focus

It won't focus on anything that's not centimeters away from the camera. I've tried all the quick fixes I have found online but with no success the camera continues to refuse to focus.

Has any one else had this problem or know how to fix it?xvideos xnxx xxx

0

threads

2

posts

6

credits

New Member

Rank: 1

credits
6
Post time 2019-8-1 19:57:02 | Show all posts
Excellent phone without 0 lags and glitches

0

threads

1

posts

4

credits

New Member

Rank: 1

credits
4
Post time 2020-2-12 15:41:06 | Show all posts
Hello!
SP flash tool is an application that mainly helps you to flash Stock ROM, Custom recovery and fixing in some extreme cases ( firmware update, Flash recovery, unbrick bricked android device, etc.) By the way, anyone searching for Kitchen Equipment Supplier. Click here https://amtc.ae/services/
You have to log in before you can reply Login | WELCOME TO UMIDIGI COMMUNITY

Points Rules

Quick Reply Top Back to list