UMIDIGI One Max V1.0_20190327 ROM - SPFT + OTA release

bencebacsi Post time 2019-4-12 04:50:37 | Show all posts [Copy link]
1 2193
View: 2193|Reply: 1

UMIDIGI One Max V1.0_20190327 ROM - SPFT + OTA release

[Copy link]
Post time 2019-4-10 09:53:05 | Show all posts |Read mode
This is the SP Flash Tool + OTA release of the
V1.0_20190327 system software
for UMIDIGI One Max

Flash tool operation is recommended to experienced users only. If you are not yet an experienced flash tool user, please carefully read the flash tool tutorial before proceeding, and strictly follow each instruction.

Except if an authorized or responsible expert directly asked you to do that,
never format the flash chip of your device or you instantly lose your warranty!

UMIDIGI One Max receives all updates automatically via FOTA method. You need this tool only in case of emergency (if you've bricked your phone), if you want to apply a clean install or if you want to clear all root access and custom recovery to make your phone able to receive FOTA updates again. Moreover, flashing with SPFT is the only option to repair (replace) damaged system software.

  • Minor bug fixes and system improvements

The system will show UMIDIGI_One_Max_V1.0_20181212 as Build number after this update but the real version is V1.0_20190327
FOTA version: UMIDIGI_One_Max_V1.0_20181212_20190327-1505

SP Flash Tool

Flashtool tutorial:

Extract the .rar file before use. The scatter file (MT6763_Android_scatter.txt) is inside the extracted folder, together with the other components

VCOM driver: Windows 10 already automatically can install it (if your computer is connected to the internet) or you can use this: MTK_Driver_Auto_Installer_SP_Drivers_20160804.exe

Here's an optional solution to start the flashing process on your UMIDIGI One Max if the standard method doesn't work.
It's especially useful if your phone is bricked or is stuck in bootloop
1. Connect your UMIDIGI One Max to USB.
2. Start the flashing process with the Download button in the flasher app.
3. Press and keep pressed the power button of your phone until the flashing process starts (red bar appears at the bottom of the app window), then release it. In this process you have to keep the power button pressed for about 10 seconds.
4. Wait until the flashing process finishes.


OTA (recovery) update
Manual (local) OTA update method instructions
  • Copy the downloaded .zip file to the internal storage of your phone
  • Go to Settings --> System --> About phone --> Wireless update
  • Tap the 3-dot menu button in the top right corner and select Local Updates
  • Brows for the file and select it
  • Select INSTALL NOW, then OK in the Warning window. Your phone reboots into recovery, the update gets installed, then your phone boots into Android. Your updated system is ready to use.

Update file for manual OTA update:
It can update version 20190129 only

Optional method (in case if the manual OTA update gets stuck): Install from recovery
You need a microSD card (with at least 4GB capacity) installed in your phone!
  • Copy the file to your SD card.
  • Press and hold the volume-up and power buttons together until your phone restarts in the boot selector mode. It needs about 10 seconds or a little bit less if your phone was already powered off.
  • Here you can move with the vol-up button and select an item with vol-down. Select Recovery.
  • Your phone boots into Recovery and you see a lying android figure with an exclamation mark in red triangle on its tummy + 'No command'.
  • Press and hold the power and vol-up buttons (in this order) together, then release them to call the recovery menu. Now you can move with both volume buttons, and select an item with the power button.
  • Move to ‘Apply update from SD card’ and select it.
  • On the next screen brows for the update file and select it. The updating process will start and needs a few minutes to be finished.
  • After a succcessful installation you can read the ''Install from SD card complete.'' message and the receovery menu is available again.
  • Select 'Reboot system now'. Alternatively you can perform a factory data reset here by choosing 'Wipe data/factory reset'

Kind request from users:
Please report any kind of new issues you experience after installing this update only if you've already flashed this ROM with SP Flash Tool in Firmware Upgrade mode. In rare cases a FOTA update can cause more or less serious malfunctions but that means only the update process went wrong, not a badly developed ROM. An updated stock ROM, especially related to the basic functions will not cause any new issues but will solve some of the existing ones.







New Member

Rank: 1

Post time 2019-4-12 04:50:37 | Show all posts
Добрый вечер! Пользуюсь телефоном уже четыре месяца, столкнулся с следующими проблемами:
- После обновления стал ОЧЕНЬ ТИХИМ разговорный динамик. Из коробки собеседника было слышна ОЧЕНЬ ХОРОШО. Обновление все испортило
- Постоянно пропадает звук на уведомления (SMS, Whats up, итак далее). Восстанавливается только после перезагрузки, но не на долго! Приходится постоянно перезагружать!
- При разговоре плохо срабатывает датчик на блок экрана. Ухом постоянно нажимается откл. микрофона, собеседник перестает тебя слышать, приходится постоянно на это обращать внимание.
- датчик приближения или света работает не корректно. Отводишь телефон от уха, экран не загорается, может мигнуть, может так и не загореться.
- Значек в WiFi в шторке очень близко расположен к дате и времени. При вкл. WiFi постоянно выходит меню будильника!

Все эти замечания относятся и к предыдущим обновлениям.

Стоковую прошивку протестировать не успел т.к. сразу после покупки обновился, но как минимум разговорный динамик был громче!

Надеюсь эти проблемы будут исправлены в будущих обновлениях! Спасибо
You have to log in before you can reply Login | WELCOME TO UMIDIGI COMMUNITY

Points Rules

Quick Reply Top Back to list