UMIDIGI One Pro V2.0_20180914 ROM - SPFT + OTA release

bencebacsi

This is the SP Flash Tool + OTA release of the

V2.0_20180914 system software

for UMIDIGI One Pro

Flash tool operation is recommended to experienced users only. If you are not yet an experienced flash tool user, please carefully read the flash tool tutorial before proceeding, and strictly follow each instruction.

Except if an authorized or responsible expert directly asked you to do that,

never format the flash chip of your device or you instantly lose your warranty!

UMIDIGI One Pro receives all updates automatically via FOTA method. You need this tool only in case of emergency (if you've bricked your phone), if you want to apply a clean install or if you want to clear all root access and custom recovery to make your phone able to receive FOTA updates again. Moreover, flashing with SPFT is the only option to repair (replace) damaged system software.

Changelog:

• Updated APN settings list
• Minor bug fixes
  

The system will show UMIDIGI_One_Pro_V2.0_20180815 as Build number after this update but the real version is V2.0_20180914

FOTA version: UMIDIGI_One_Pro_V2.0_20180815_20180914-2203

--------------------------------------------------------------------------------

SP Flash Tool

Resources:

Flashtool tutorial: http://bit.ly/SPFTguide

ROM: >>> UMIDIGI_One_Pro_V2.0_20180914.V3.07.rar <<<

Extract the .rar file before use. The scatter file (MT6763_Android_scatter.txt) is inside the extracted folder, together with the other components

SPFT: SP_Flash_Tool_v5.1836.rar

VCOM driver: Windows 10 already automatically can install it (if your computer is connected to the internet) or you can use this: MTK_Driver_Auto_Installer_SP_Drivers_20160804.exe

Here's an optional solution to start the flashing process on your UMIDIGI One Pro if the standard method doesn't work.

It's especially useful if your phone is bricked or is stuck in bootloop

1. Connect your UMIDIGI One Pro to USB.

2. Start the flashing process with the Download button in the flasher app.

3. Press and keep pressed the power button of your phone until the flashing process starts (red bar appears at the bottom of the app window), then release it. In this process you have to keep the power button pressed for about 10 seconds.

4. Wait until the flashing process finishes.

--------------------------------------------------------------------------------

OTA (recovery) update

Manual (local) OTA update method instructions

• Copy the downloaded .zip file to the internal memory of your phone
• Go to Settings --> System --> About phone --> Wireless update
• Tap the 3-dot menu button in the top right corner and select Local Updates
• Brows for the ...update.zip file and select it
• Select INSTALL NOW, then OK in the Warning window. Your phone reboots into recovery, the update gets installed, then your phone boots into Android. Your updated system is ready to use.
  

Update file for manual OTA update: >>> UMIDIGI_One_Pro_V2.0_20180815_20180914-2203_update.zip <<<

It can update version 20180903 only

Optional method (in case if the manual OTA update gets stuck): Install from recovery

You need a microSD card (with at least 4GB capacity) installed in your phone!

• Copy the ...update.zip file to your SD card.
• Press and hold the volume-up and power buttons together until your phone restarts in the boot selector mode. It needs about 10 seconds or a little bit less if your phone was already powered off.
• Here you can move with the vol-up button and select an item with vol-down. Select Recovery.
• Your phone boots into Recovery and you see a lying android figure with an exclamation mark in red triangle on its tummy + 'No command'.
• Press and hold the power and vol-up buttons (in this order) together, then release them to call the recovery menu. Now you can move with both volume buttons, and select an item with the power button.
• Move to ‘Apply update from SD card’ and select it.
• On the next screen brows for the update file and select it. The updating process will start and needs a few minutes to be finished.
• After a succcessful installation you can read the ''Install from SD card complete.'' message and the receovery menu is available again.
• Select 'Reboot system now'. Alternatively you can perform a factory data reset here by choosing 'Wipe data/factory reset'
  

Kind request from users:
Please report any kind of new issues you experience after installing this update only if you've already flashed this ROM with SP Flash Tool in Firmware Upgrade mode. In rare cases a FOTA update can cause more or less serious malfunctions but that means only the update process went wrong, not a badly developed ROM. An updated stock ROM, especially related to the basic functions will not cause any new issues but will solve some of the existing ones.

dawidchelminski

Please upgrade to Android 9.0. Please add gesture control. Add more control to the brightness settings.

jaycyn91

thanks for fixes hoping for a faster shutter speed or some options for camera and phone would be almost perfect keep up the great work.

tarik3344

hello, what is the purpose of this forum, if there is no one who answers our questions, I noticed that umidigi developers do not communicate with their customers.

Uxon

\n\nAndroid Oreo is a good system and it would be interesting to integrate Treble on the phone to be able to update it more often. In the meantime I have disabled the virtual navigation buttons to install my own navigation application with gestures. I remember we had an option to enable the root from the developer options with the umidigi s2 lite. This option was cool and it's a pity that it is no longer there. I will try to install magisk.

tarik3344

I'm still not able with this update to receive apps notifications because I've noticed that most apps do not start automatically at phone startup

dawidchelminski

I would also like to have different resolutions in the camera, and the aspect ratio of the screen in the video.

tarik3344

How to install ota update in twrp in rooted device

SterliYork

flash stock recovery and stock boot

zolotov23

autorun applications are not implemented. for example viber. if you restart the phone, then the messages do not come, you need to tap on the application and it starts working, notifications come. so with all the applications. even with the mail. until one time you do not tap the letters will not come. make it as in s2 lite, there was setting up autorun applications.