Recover dead fingerprint scanner Android 8.1 [CLOSED]

Dpot1

diabloksm replied at 2018-2-10 08:14
You need only to press the start button and then connect your switched off phone. A tip: try to disa ...

if you mean power ive done that and it goes into fully booting the phone

bencebacsi

Dpot1 replied at 2018-2-10 08:18
if you mean power ive done that and it goes into fully booting the phone

You don't have to press any button on the phone. Do you mean, you can't even connect your phone in preloader mode? Then how could you flaash it with the flash tool? After switching into meta mode (the boot logo appears), you might need to disconnect and reconnect your phone but the preloader mode at the beginning should not cause any issue.

Dpot1

bencebacsi replied at 2018-2-10 08:30
You don't have to press any button on the phone. Do you mean, you can't even connect your phone in  ...

I can use the SP tool but no matter what I do it doesnt work. If I plug it in pressing no buttons it just goes to the battery charging. It says connected to phone then says the Wait Soter message and I ran it for 30 minutes, it just doesnt work

Dpot1

bencebacsi replied at 2018-2-10 08:30
You don't have to press any button on the phone. Do you mean, you can't even connect your phone in  ...

How long should it take? If i unplug the phone with it turned off, then run the software and plug it in it says phone connect then goes to Wait Soter and just continues to run.
The log file if opened displays the below continuously

[2018/2/10 00:48:18] microtrust_log: dll version is v1.3.0, sp_meta_transfer_data() line number:537 call meta function failed;        return value=12
[2018/2/10 00:48:18] microtrust_log: dll version is v1.3.0, send_command_to_phone() line number:1253 transfer_data_result != TRANSFER_DATA_SUCCESS, transfer data failed;        return value=-3
[2018/2/10 00:48:18] microtrust_log: dll version is v1.3.0, check_soter_status() line number:1388 send command failed;        return value=-3

bencebacsi

Dpot1 replied at 2018-2-10 08:52
How long should it take? If i unplug the phone with it turned off, then run the software and plug  ...

Once boot your phone normally into android, power it off normally (not forcing with long press power button), then try again.

millino

bencebacsi replied at 2018-2-10 09:25
Once boot your phone normally into android, power it off normally (not forcing with long press pow ...

doesn't work.....no boot logo....nothing...sp Flash tool works perfectly...

bencebacsi

millino replied at 2018-2-10 19:18
doesn't work.....no boot logo....nothing...sp Flash tool works perfectly...

And what about the SN Writer Tool? Can you use it? That tool also works in meta mode.

Dpot1

No can't use SN writer same issue

bencebacsi

Dpot1 replied at 2018-2-11 00:33
No can't use SN writer same issue

You also need the SN Writer to recover your original IMEI numbers.
Try to replace the preloader com port driver, maybe you have an outdated version installed. Your computer should be connected to the internet.
1. Open your Windows device manager.
2. Connect your powered off phone to USB and as soon as the preloader com port pops up in the device list, right click on it and remove the device together with its driver. You must be quick with your right click.
3. Disconnect and reconnect your phone to let the new drivers get installed.
4. Disconnect your phone and try again to use the activation tool.

Dpot1

So I have to use SN Writer to recovered the IMEIs or it wont work?