UMIDIGI C NOTE 2 V1.6_20170725 ROM - QGDP + SPFT release

bencebacsi Post time 2017-8-8 23:19:48 | Show all posts [Copy link]
103 13171
Author: bencebacsi

UMIDIGI C NOTE 2 V1.6_20170725 ROM - QGDP + SPFT release

[Copy link]

0

threads

8

posts

39

credits

New Member

Rank: 1

credits
39
Post time 2017-8-8 00:08:59 | Show all posts
I exactly repeated your actions - the program does not find the phone. All drivers installed, checked - they've installed fine. Apparently the problem still in the phone. And another question: why would the program access the Internet? if the Internet is disabled on your computer, it won't even start .

0

threads

8

posts

33

credits

New Member

Rank: 1

credits
33
Post time 2017-8-8 00:40:12 | Show all posts
Бо replied at 2017-8-7 22:56
Hi, you can watch my video https://www.youtube.com/watch?v=elWbsndbnA8 , you just need to press th ...

I've followed every step, but the phone continuously connect then disconnect, if my phone connect like your phone i think i can fix my problem.

0

threads

8

posts

33

credits

New Member

Rank: 1

credits
33
Post time 2017-8-8 00:56:09 | Show all posts
bencebacsi replied at 2017-8-6 12:16
I could translate the Chinese only resources of the other flasher app, called QGPD.
QGPD: QGDP_Assem ...

I've followed every step, but the phone continuously connect then disconnect.....  About what steps should be done to connect phone to PC, I also have installed a lot of Mediatek USB Driver but did not succeed.

Comments

Have you tried to use a differente USB cable? With mi UMI Rome sometimes the SPFT do a similar problem, and with myps4 usb cable I coul fix it and flash my phone. Good luck friend :)  Post time 2017-8-8 01:08
 Author| Post time 2017-8-8 02:18:14 | Show all posts
Please let me know what kind of com port you see in the device manager after connecting your phone. You should see this:
preloader.jpg


The number of the com port doesn't make sense.

0

threads

5

posts

34

credits

New Member

Rank: 1

credits
34
Post time 2017-8-8 02:42:11 | Show all posts
Edited by poxudister at 2017-8-8 02:43 \n\nI have this on 3 different computers with installed drivers.

Без имени-1.jpg
 Author| Post time 2017-8-8 03:23:11 | Show all posts
poxudister replied at 2017-8-8 02:42
Edited by poxudister at 2017-8-8 02:43 \n\nI have this on 3 different computers with installed driv ...

Then the preloader of your phone does not work, its partition has been wiped or damaged. SP Flash Tool can repair it. If you select the preloader partition only and uncheck all other partitions, SPFT will be able to accept the MediaTek USB Port connection and flash the preloader partition. Next time the preloader will work (your phone will connect as preloader com port), and you'll be able to flash your phone normally. However, it's about SP Flash Tool but you can't configure QGPD to flash only the preloader partition. If you haven't tried it yet, try to flash only the preloader partition with SP Flash Tool.

0

threads

8

posts

39

credits

New Member

Rank: 1

credits
39
Post time 2017-8-8 14:23:59 | Show all posts
I tried flash only the preloader partition with SP Flash Tool - the error is the same "ERROR STATUS_EXT_RAM_EXCEPTION (0xc0050005)".
I tried to clamp the button volume down, tried to clamp all three buttons at once - no result.
 Author| Post time 2017-8-8 20:14:49 | Show all posts
mthd replied at 2017-8-8 14:23
I tried flash only the preloader partition with SP Flash Tool - the error is the same "ERROR STATUS_ ...

Did you try without pressing any button?

0

threads

8

posts

39

credits

New Member

Rank: 1

credits
39
Post time 2017-8-8 23:15:01 | Show all posts
bencebacsi replied at 2017-8-8 20:14
Did you try without pressing any button?

Yes, I tried and now tried again - didn't hold any buttons, and downloaded only the preloader. Same error as always.

0

threads

15

posts

72

credits

Senior Member

Rank: 2

credits
72
Post time 2017-8-8 23:19:48 | Show all posts
8. Press and hold the volume-down button of your phone and connect it to USB - Your phone must be powered off. (As soon as your port gets added to the list, release the vol-down button or your phone will boot into factory mode)

...The phone was connected and disconnected then loop same like I try with SPFT before.
You have to log in before you can reply Login | WELCOME TO UMIDIGI COMMUNITY

Points Rules

Quick Reply Top Back to list